
43
Mixing
The parameters that can be set for each type of track are as follows.
Mono tracks: 1–8
Stereo tracks: 1/2–7/8
Display Parameter
Setting range
(default value)
Explanation
Mono
tracks
Stereo
tracks
Master
track
PAN
PAN
L100~R100
(Center)
Adjusts a track’s PAN. For stereo tracks adjusts the volume
balance between the left and right channels.
◯ ◯
EQ HI High-frequency range boost/cut
EQ HI
TYPE
EQ HI, HI CUT
(EQ HI)
Set whether to boost/cut the high-frequency range (
EQ HI
)
or clearly cut unnecessary high frequencies (
HI CUT
). This
parameter can only be accessed when
EQ HI
is on.
◯ ◯
GAIN
–12dB~12dB
(0dB)
Adjust amount of boost/cut of high frequencies by -12 ~ +12
dB. This parameter is shown only when the
TYPE
is set to
EQ
HI
. When set to
HI CUT
, it is not shown.
◯ ◯
FREQUENCY
500Hz~18kHz
(8.0kHz)
Adjust the EQ boost/cut frequency of high frequencies. This
parameter can only be accessed when
EQ HI
is on.
◯ ◯
EQ MID Middle-frequency range boost/cut
EQ MID
GAIN
–12dB~+12dB
(0dB)
Adjust amount of boost/cut of middle frequencies by -12 ~
+12 dB. This parameter can only be accessed when
EQ MID
is on.
◯ ◯
FREQUENCY
40Hz~18kHz
(1.0kHz )
Adjust EQ boost/cut frequency of middle frequencies. This
parameter can only be accessed when
EQ MID
is on.
◯ ◯
Q
0.1~2.0
(0.5)
Adjust the width of the middle frequency band affected. This
parameter can only be accessed when
EQ MID
is on.
◯ ◯
EQ LOW Low-frequency range boost/cut
EQ LO
TYPE
EQ LO, LO CUT
(EQ LO)
Set whether to boost/cut the low-frequency range (
EQ LO
)
or clearly cut unnecessary low frequencies (
LO CUT
). This
parameter can only be accessed when
EQ LO
is on.
◯ ◯
GAIN
–12dB~+12dB
(0dB)
Adjust amount of boost/cut of low frequencies by -12 ~+12
dB. This parameter is shown only when the
TYPE
is set to
EQ
LO
. When set to
LO CUT
, it is not shown.
◯ ◯
FREQUENCY
40Hz~1.6kHz
(125Hz)
Adjust EQ boost/cut frequency of low frequencies. This
parameter can only be accessed when
EQ LO
is on.
◯ ◯
Effect send levels
REV SEND
REVERB
SEND LEVEL
0~100
(0)
Adjust the signal level sent from the track to the reverb effect.
◯ ◯
CHO SEND
CHORUS/
DELAY SEND
LEVEL
0~100
(0)
Adjust the signal level sent from the track to the chorus/delay
effect.
◯ ◯
FADER
FADER
0~127
(100)
Adjust the current volume.
◯ ◯ ◯
ST LINK
STEREO LINK
On/Off
(Off)
Switch on/off to set the stereo link function that
connects two mono tracks together.
◯ ◯
INVERT
INVERT
On/Off
(Off)
Set whether the phase of a track is inverted or not. Set it to
Off
to use normal phase or
ON
to invert the phase.
◯ ◯
NOTE
●
Use the ON/OFF soft key to turn EQ HI,
EQ MID, EQ LO, REV SEND, CHO SEND and
INVERT parameters ON/OFF.
●
When a stereo link is ON, the INVERT
parameter is shown as INVERT L for the
odd track, and as INVERT R for the even
track.
Comentarios a estos manuales