
R24 Effect types and parameters
Effect types and parameters 10
Table 1
Parameters marked with allowvaluestobesetinnoteunits,usingthesong/patterntempoasreference.
The note durations for the setting values are shown below.
32ndnote Dotted16thnote Dotted8thnote
Delay,AnalogDelay
andEchocanuse
uptox8.
ReverseDelay can
useuptox4.
16thnote 8thnote Quarternote
:
Quarternotetriplet Half note triplet Dottedquarternote
Table 2
Setting Explanation
Off
Frequency does not change.
Up
Frequency changes from minimum to maximum
along with the controlling waveform.
Down
Frequency changes from maximum to minimum
along with the controlling waveform.
Hi
Frequency changes from patch setting to maximum
along with the controlling waveform.
Lo
Frequency changes from minimum to patch setting
along with the controlling waveform.
Table 3
Setting Explanation Setting Explanation
Up Saw
Rising sawtooth wave
Tri
Triangular wave
Up Fin
Risingfinwave
TrixTri
Squared triangular wave
DownSaw
Falling sawtooth wave
Sine
Sine wave
DownFin
Falling fin wave
Square
Square wave
Table 4
Setting Explanation Setting Explanation
8thnote
1 bar
1measure
Quarternote
2 bars
2measures
Half note
3 bars
3measures
Dottedhalfnote
4 bars
4measures
Table 5
•Thenoterangeactuallyavailabledependsontheparameter.
•Dependingonthecombinationof temposettingandselectednotesymbol,the parametervariationrangecouldbe exceeded.Insuch a
case,thevalueisautomaticallyhalved(orsetto1/4iftherangeisstillexceeded).
NOTE
Setting Explanation
1
1semitonelower
→
original sound
2
Original sound
→
1semitonelower
3
Doubling
→
detune + original sound
4
Detune+originalsound
→
doubling
5
Original sound
→
1octavehigher
6
1octavehigher
→
original sound
7
Original sound
→
2octaveslower
8
2octaveslower
→
original sound
9
1octavehigher + original sound
→
1octavelower +
original sound
10
Complete fifth down + original sound
→
complete
fourth up + original sound
11
Complete fourth up + original sound
→
complete fifth
down + original sound
12
0Hz+originalsound
→
1octaveup
13
1octaveup
→
0Hz+originalsound
14
0Hz+originalsound
→
1octaveup+originalsound
15
1octaveup+originalsound
→
0Hz+originalsound
16
1octaveup+originalsound
→
0Hz+originalsound
Module 1~8
Unit Type Setting range Explanation
HPF Freq
HPF
80~240Hz Sets the cut off frequency.
This filter cuts low frequencies and passes high-frequencies.
Comp Type
RackComp
Foranexplanationoftypesandparameters,seeCLEAN,DISTORTION,
ACO/BASSSIMalgorithms.
Limiter
EQ Type
SeetheBASSalgorithmfordetails.
8x Comp EQ algorithm
Mastering algorithm
Type Parameters
3Band Comp
Xover Lo Xover Hi Sense Hi Sense Mid Sense Low Mix High Mix Mid Mix Low
Compressorthatdividessignalinto3bandsthatcanbecompressedandmixedseparately.
Lo-Fi
Foranexplanationofthetypesandparameters,seetheSTEREOalgorithm.
• COMP/Lo-Fi module
Parameter descriptions
Parameter Setting range Explanation
Xover Lo
50Hz~16kHz
Adjusts low-to-mid crossover frequency.
Xover Hi
50Hz~16kHz
Adjusts mid-to-high crossover frequency.
Sense Hi
0~24
Adjusts high range compressor sensitivity.
Sense Mid
0~24
Adjusts mid range compressor sensitivity.
Sense Low
0~24 A
djusts low range compressor sensitivity.
Mix High
Off,−24~6 Adjusts high frequency range mix level.
Mix Mid
Off,−24~6 Adjusts mid frequency range mix level.
Mix Low
Off,−24~6 Adjusts low frequency range mix level.
Comentarios a estos manuales